Rivet tools can fix many things, such as aircraft, automobiles and household appliances, which may be used regardless of the size of the job. Of course, the use of rivets must have a rivet gun. To make a riveting gun, start with a pre-staked aluminum handle and immediately insert a steel sleeve to store the hydraulic fluid. Next, install the spring of the rivet gun trigger, tighten an aluminum disc on the chassis, and fix the two parts with the gun handle, which forms the head part of the nail gun.
The is used to place rivets on the tiny opening, and after the gun head is lubricated, it is pressed into the chamber of the nail ramming gun, that is, the screw is screwed on the top of the nail ramming gun handle to prevent hydraulic oil from overflowing when in use. The hydraulic oil is initially injected from the bottom of the sleeve, even if the pneumatic piston is installed in the fluid-filled sleeve and the screw is screwed in the head of the rivet gun, which ensures that the internal equipment will not be dislocated during the subsequent assembly process. Put the chassis on the air chamber, connect the air pipe, fix it with a wrench, connect the air source device, and then press the trigger to press the hydraulic pressure inside the rivet gun, so as to start working. Now test it. The technician places a rivet at the muzzle of the rivet gun, then inserts the other end of the rivet into the hole in the test tray and presses the trigger on the rivet gun. The rivet will be firmly fixed in the hole of the test plate. Now the rivet is produced. It is made of round steel wire. The machine cuts the steel wire into small pieces of fixed length. The small pieces of steel wire are hit into the window mold twice to make the ice core.
The machine runs very fast and can produce 200 nail cores in a minute. The ice core is filled into the upper shell groove of the rivet core from the jagged filling wood through the filling mother, the rivet gun can firmly grasp the rivet groove, and the rivet type can be installed to be powered off, which is the contrast before and after the rivet is filled. The rivets made by this machine are hit five times, and the steel wire forms a hollow nail body. The machine can make 300 crystals a minute. The lower nail body enters the roller for cleaning to remove the residual oil stain in the mold filling process. The ice core is also thoroughly cleaned and then sent to a high temperature furnace. This intense heating and slow cooling process can strengthen the crystal and eliminate the internal stress. After the crystal surface is galvanized, it goes to the next station. The ice core will pass through a wider and wider transmission channel. The channel can pick out the nail core that is too big or too small. The magnetic equipment will collect the nail core of the right size, and the unqualified ones will be discarded. The nail core is absorbed on the magnetic equipment.
The nail is embodied in a rotating machine, and the rotating machine temporarily pauses to let the nail. After inserting the rivet body, the above is a slow motion, in fact, the selection machine runs very fast, and can make millions of rivets a day, so the rivet is made. Can fix a lot of things, products fixed by rivets include aircraft, automobiles and household appliances, etc., regardless of the size of the work may use rivets. Of course, the use of rivets must have a rivet gun.
A riveting gun starts with a pre-staked aluminum handle and immediately inserts a steel sleeve that stores the hydraulic fluid. Next, install the spring of the rivet gun trigger, tighten an aluminum disc on the chassis, and fix the two parts with the gun handle, which forms the head part of the nail gun. It is used to place the rivet on the tiny opening. After the lubricant is applied to the gun head, it is pressed into the chamber of the nail ramming gun, that is, the screw is screwed on the top of the nail ramming gun handle to prevent the hydraulic oil from overflowing during use. The hydraulic oil is initially injected from the bottom of the sleeve, even if the pneumatic piston is installed in the fluid-filled sleeve and the screw is screwed in the head of the rivet gun, which ensures that the internal equipment will not be dislocated during the subsequent assembly process. Put the chassis on the air chamber, connect the air pipe, fix it with a wrench, connect the air source device, and then press the trigger to press the hydraulic pressure inside the rivet gun, so as to start working.
Now test it. The technician places a rivet at the muzzle of the rivet gun, then inserts the other end of the rivet into the hole in the test plate and presses the trigger of the rivet gun. The rivet will be firmly fixed in the hole of the test plate. Now the rivet is produced. It is made of round steel wire. The machine cuts the steel wire into small pieces of fixed length. The small pieces of steel wire are hit into the window mold twice to make the ice core. The speed of the machine is very fast, and it can make 200 nail cores in a minute. The ice core is filled into the upper shell groove of the rivet core from the jagged filling wood through the filling mother, the rivet gun can firmly grasp the rivet groove, and the rivet type can be installed to be powered off, which is the contrast before and after the rivet is filled. The rivets made by this machine are hit five times, and the steel wire forms a hollow nail body. The machine can make 300 crystals a minute.
The nail body below that enter the roller to be clean, and residual oil stains in the mold filling process are remove. The ice core is also thoroughly cleaned and then sent to a high temperature furnace. This intense heating and slow cooling process can strengthen the crystal and eliminate the internal stress. After the crystal surface is galvanized, it goes to the next station. The ice core will pass through a wider and wider transmission channel. The channel can pick out the nail core that is too big or too small. The magnetic equipment will collect the nail core of the right size, and the unqualified ones will be discarded. The nail core is absorbed on the magnetic equipment. The nail is embodied in a rotating machine, and the rotating machine temporarily pauses to let the nail. After inserting the rivet body, the above is a slow motion, in fact, the selection machine runs very fast, and can make millions of rivets a day, so the rivet is made.
hello, everyone. Today I will show you a rivet tool. The rivet tool is placed on the electric hand drill. Let’s try to install the rivet first. If we make a hole, we must press it inside. Then the electric hand drill turns forward. Then hold it tight. That’s how it went in. Then press reverse to back it out. It’s very convenient, and then because of the electric hand drill, the general work is available. This one, this one. Rivet head is a very practical and convenient small tool. When you enter, the flashlight section turns forward, and then the rivet is pulled off, and then it reverses, and its tail comes out. Is it a very convenient and practical small accessory? Then the rod of the electric hand drill is reversed. Get him out of there. That’s all right. It’s an electric hand drill, and then it can be matched with this head. A very convenient small tool to introduce to you, today’s video to share with you here, if you like me, you can follow me.A riveting gun starts with a pre-staked aluminum handle and immediately inserts a steel sleeve that stores the hydraulic fluid. Next, install the spring of the rivet gun trigger, tighten an aluminum disc on the chassis, and fix the two parts with the gun handle, which forms the head part of the nail gun. It is used to place the rivet on the tiny opening. After the lubricant is applied to the gun head, it is pressed into the chamber of the nail ramming gun, that is, the screw is screwed on the top of the nail ramming gun handle to prevent the hydraulic oil from overflowing during use. The hydraulic oil is initially injected from the bottom of the sleeve, even if the pneumatic piston is installed in the fluid-filled sleeve and the screw is screwed in the head of the rivet gun, which ensures that the internal equipment will not be dislocated during the subsequent assembly process. Put the chassis on the air chamber, connect the air pipe, fix it with a wrench, connect the air source device, and then press the trigger to press the hydraulic pressure inside the rivet gun, so as to start working.
Now test it. The technician places a rivet at the muzzle of the rivet gun, then inserts the other end of the rivet into the hole in the test plate and presses the trigger of the rivet gun. The rivet will be firmly fixed in the hole of the test plate. Now the rivet is produced. It is made of round steel wire. The machine cuts the steel wire into small pieces of fixed length. The small pieces of steel wire are hit into the window mold twice to make the ice core. The speed of the machine is very fast, and it can make 200 nail cores in a minute. The ice core is filled into the upper shell groove of the rivet core from the jagged filling wood through the filling mother, the rivet gun can firmly grasp the rivet groove, and the rivet type can also be installed to be powered off, which is the contrast before and after the rivet is filled. The rivets made by this machine are hit five times, and the steel wire forms a hollow nail body. The machine can make 300 crystals a minute. The lower nail body enters the roller for cleaning to remove the residual oil stain in the mold filling process. The ice core is also thoroughly cleaned and then sent to a high temperature furnace. This intense heating and slow cooling process can strengthen the crystal and eliminate the internal stress. After the crystal surface is galvanized, it goes to the next station. The ice core will pass through a wider and wider transmission channel. The channel can pick out the nail core that is too big or too small. The magnetic equipment will collect the nail core of the right size, and the unqualified ones will be discarded. The nail core is absorbed on the magnetic equipment. The nail is embodied in a rotating machine, and the rotating machine temporarily pauses to let the nail. After inserting the rivet body, the above is a slow motion, in fact, the selection machine runs very fast, and can make millions of rivets a day, so the rivet is made. Hi, everyone. Today, I will show you a rivet tool. The rivet tool is placed on the electric hand drill. Let’s try to install the rivet first. If we punch a hole, we must press it inside. Then the electric hand drill turns forward. Then hold it tight. That’s how it went in. Then press reverse to back it out. It’s very convenient, and then because of the electric hand drill, the general work is available. This one, this one. Rivet head is a very practical and convenient small tool. When you enter, the flashlight section turns forward, and then the rivet is pulled off, and then it reverses, and its tail comes out. Is it a very convenient and practical small accessory? Then the rod of the electric hand drill is reversed. Get him out of there. That’s all right. It’s an electric hand drill, and then it can be matched with this head. A very convenient small tool to introduce to you, today’s video to share with you here, if you like me, you can follow me.
