Hey, I want to show you how I usually pull the nail out of the wood. When doing OEM, it often involves demolition, or the wood in the house needs to be demolished. The biggest problem you face is the nail screw, which is a little easier to handle. The tool you need is nail puller. Of course, this kind of hammer with a small hook on it is more suitable.
Another essential nail puller is this kind of nail puller. I have used many nail pullers. At present, at a relatively affordable price level, the best nail puller I have used is this one. The link to my visual tool is also in the description area of the video. Well, let’s show you how to pull out the nail now.
Then I will pick two nails first. In fact, it is also a relatively simple situation.This tool is called na play, and it is called cat’s paw. Its main function is to pull out the nail. Er, the reason for this design is that it has a relatively small angle. In this way, if the nail comes out a little, or you can easily get the nail head stuck in it, you can directly pinch it on the head of the nail and pull it out. If the nail is very deep, then you need to use this tip to smash it in.Then pull out the nail. I’ll show you how to use this tool. When you knock, don’t get the head stuck directly.On the head of the nail, because in this case, because it has not yet gone down into the nail, it is very easy to tilt up the edge of the head of the nail. In this case, it will lose its grip. So you have to have a little distance, about five millimeters, and then knock it in. When you knock in a little bit, slowly tilt it.
Then in general, like my new nail, there is no rust, so it comes out as soon as it is broken off. If it is a very old nail with rust, then you have to do this. Don’t scratch like this when you use it. If you scratch like this, you are likely to press your fingers. You have to hold it like this. In this way, the nail will come out, and then you can use the hammer.You can also use this place, but you can also pull it like this. If the nail is easier to lift, you can pull it like this. If the nail is more difficult, in general, if you want to remove the nail, the nail will be rusty, or the plating is very rough, so it is more difficult. You should pay attention to whether there is a small groove in your hammer. The function of this small groove is to make a nail, so it can be clamped. Clamp it and break it out like this.And then after you clamp it, you can, you can also break it like this, but it’s very laborious. The correct way is to clamp it, and then swing it sideways. Don’t break it directly. After breaking it like this.
It comes forward and then goes in the opposite direction, and then it comes back to the root and then goes in the opposite direction. After several rounds, after several rounds, the nail is easy to come out in this shape. Then, I hit the nail a little deeper to see what we should do with this deep nail. Then I hit the nail a little deeper. I use cloves, which is more convenient. Next, I use the ice gun to make two holes in these two, one shallow 1.One is a little bit deeper, so look at how these two should be operated in the same way. However, I replaced this head with this one. This head can be knocked a little deeper, and then repeat the operation just now. The position of this head is still a little bit higher, leaving about five millimeters. Then, hit it with a hammer. Adjust the direction, gradually lift up, and then continue to hit.
Then when this sharp point, uh, gradually enters the cake of the nail, uh, it stands up and hits it again twice. You can easily see that this is made of nail incense. There is a layer of glue outside the nail of the nail gun. That is to say, after it is driven in at a high speed, the glue adheres to the wood, so there is a certain resistance when it is pulled out. It is not like the nail I just used with a hammer, which is easy to pull out. If you hang it down and have this function, you can pull it out like this.After you put it in and pull it like this, it’s easy to pull it out, and then clamp it in the opposite direction, and then clamp it back in the opposite direction. Then let’s look at the deeper one. The deeper the distance is, the longer it is. He was clamped. It was actually very, very difficult to pull out the nail. The quality of the gun was really good.The reason for the failure to pull out the nail was that the nail gun was with glue, and it was really too deep, so it was completely stuck in the wood, and my nail head was almost broken, but it still couldn’t be pulled out.
Ok, that’s all for the technique of pulling nails out of wood. If you want to read more articles about carpentry, we’ll see you next time. Bye-bye.
